- 您现在的位置：买卖IC网 > Sheet目录310 > AL8400SE-7 (Diodes Inc)IC CTRLR LED DRIVER SOT353
AL8400 /AL8400Q
Application Information
Description
The AL8400 Linear LED driver controller uses an external pass element to drive the LEDs and uses its FB pin to sense the LED current through
an external resistor R SET . The pass element is driven by the AL8400’s open collector OUT pin which allows the pass element to be either an
NPN transistor or N-channel MOSFET. An external pull-up resistor, R B , is required to be connected from the OUT pin to V CC . This resistor
supplies the output bias current of the AL8400 together with any current which the pass element requires.
In order to maintain the accuracy of the 200mV reference voltage on the FB pin the value of R B should be set so that the OUT pin sinks 1mA.
Stability
As with all ICs, for best stability a 0.1μF minimum (X7R ceramic) power supply decoupling capacitor, C D , connected between V CC and Ground
(See Figure 2) is recommended. C D should be placed as close to the V CC pin as possible < 5mm.
Figure 2 Application Circuit Using Bipolar Transistor
The AL8400 requires an output capacitor, C L in Figure 2, to be connected from the OUT pin to Ground. This capacitor is required to compensate
the current control loop of the AL8400.
This compensation capacitor must be placed as close to the OUT pin as possible < 5mm. If the PCB traces are too long, there is the possibility of
oscillation at about 5MHz. The capacitors C D and C L must be mounted immediately adjacent to the AL8400, with direct connections to OUT, E1,
GND and V CC . The limit of 5mm provides a good margin for stability.
The value of capacitor C L is determined from the value of the pull-up resistor R B so that:
C L x R B ≥ 2ms
For example if R B = 1k Ω , then C L must be 2μF or greater. The recommended capacitor type is X7R ceramic.
200
225
150
100
50
0
-50
Gain
Phas e
V = =
V OUT OUT 0.6V
C 1k =
R B = OUT ? 2.2uF
C L = 2.2μF
180
135
90
45
0
1
10
100
1k
10k
100k
1M
Frequency (Hz)
Figure 3 Gain and Phase vs. Frequency with R B = 1k ? and C L = 2.2μF
AL8400/ AL8400Q
Document number: DS35115 Rev. 4 - 2
5 of 13
www.diodes.com
August 2012
? Diodes Incorporated
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
AL8805W5-7
IC REG SW CONV BUCK ASYNC SOT-23
AL8806MP8-13
IC LED DVR CONS CURR 8MSOP
AL8807W5-7
IC LED DRVR DCDC BUCK SOT25
AL9910AS-13
IC LED DRVR HIGH BRIGHT SO8EP
ALC60481R05
PWR SUP AC-DC 6-48V 1.05A 50.4W
ALV100362R5
POWER SUPPLY AC-DC 36V 2.5A 90W
ALV60361R7
POWER SUPPLY AC-DC 36V 1.7A 61W
ALV80126R5
POWER SUPPLY AC-DC 12V 6.5A 78W
相关代理商/技术参数
AL841B
制造商:ELC 功能描述:PSU BENCH MULTI OUTPUT 制造商:ELC 功能描述:PSU, BENCH, MULTI OUTPUT, EURO
AL8504
制造商:Molex 功能描述:
AL-85-120VAC
制造商:Carlo Gavazzi 功能描述:LATCH UNIT 50-85A
AL875
制造商:未知厂家 制造商全称:未知厂家 功能描述:Triple High Speed, 8-bit Analog-to-Digital Converter
AL8805
制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:HIGH EFFICIENCY 30V 1A BUCK LED DRIVER
AL8805EV1
功能描述:AL8805 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:680mA 输出和类型:1，非隔离 电压 - 输出:- 特性:可调光 电压 - 输入:6 V ~ 36 V 所含物品:板 使用的 IC/零件:AL8805 标准包装:1
AL8805EV2
功能描述:AL8805 1, Non-Isolated Output LED Driver Evaluation Board 制造商:diodes incorporated 系列:- 零件状态:有效 电流 - 输出/通道:680mA 输出和类型:1，非隔离 电压 - 输出:- 特性:- 电压 - 输入:12VAC，12 V ~ 20 V 所含物品:板 使用的 IC/零件:AL8805 标准包装:1
AL8805W5-7
功能描述:LED照明驱动器 HI EFF 30V 1A BUCK LED DRIVER RoHS:否 制造商:STMicroelectronics 输入电压:11.5 V to 23 V 工作频率: 最大电源电流:1.7 mA 输出电流: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:SO-16N